Skirting board radiators are a child's play and competent income of heating a time. The ground wire on all models is attached to a screw or bolt that is connected to the metal heater housing. Loosen the screw or bolt and pull the ground wire off of the connector.4. Replacing a skirting board heater is great within the capabilities of most homeowners once they shift close with the equitable procedures.
Instructions
Remove the Old Radiator
1. Disconnect the gift to the getting on skirting board radiator. Allot the Correct breaker on the home breaker panel and proceeding the switch to the "Off" position. Turn the skirting board radiator thermostat to the highest setting and wait a meagre minutes. Probation the radiator to detect whether it is heating up. Provided it is heating up, it money you get closed the bad breaker.
2. Disconnect the wiring from the aged radiator. The fossil radiator Testament keep two insufficient access covers on the front, one at Everyone point of the radiator. Remove the comprehend from the butt end where the wiring comes outside of the wall and into the radiator. Provided you are not positive which speck is connected, then simply catch your first-rate guess. Pry the involve off, or remove any retaining screws and pull the include off. Whether you create not gape any wires at the end the incorporate, it way that the radiator is wired at the other speck. Bring a non-contact voltage detector to within 1/2 inch of the wires that you flash inside. Provided the voltage detector lights up, it indicates that the wires are all the more energized.
3. Disconnect the doddering wires. On most models the two vital wires are connected by wire nuts. Rotate the wire nuts counterclockwise until the wires are released, and then seperate the wires from Everyone other. On other models the borderline wires terminate at screw connections. Loosen the terminal screws and then remove the wires. The radiator consists of an electrical heating Component that runs most of the length of the radiator. The heating Component is combined with heat fins to correct the heating efficiency, and is surrounded by a episode metal housing that is designed to dominion the air flow all over the Component while preventing nation and objects from contacting the baking surfaces. The filled meeting fits wittily along the skirting board, and is normally placed under windows to combat below freezing air drafts.
Remove the mature radiator from the wall. Inspire down at floor comparable and see into the upper aperture that runs along the front of the radiator. You Testament distinguish screws that pass over holes at the back of the radiator housing and into the wall. Remove all screws that you espy. Gently wiggle the radiator to receive it to Proceeds from the wall, and then pull it out. Be careful not to damage the wall. An old radiator will usually stick a little to the drywall or plaster of the wall, or be glued to the wall with old paint. Applying too much force can cause pieces of the wall to come away with the old radiator.
Install the New Radiator
5. Remove the access cover from the wiring compartment of the new baseboard radiator latest closest to the wires coming out of the wall. Pry the cover off with a screwdriver, or remove any retaining screws and pull the cover off, as appropriate. Use a screwdriver to punch out the perforated metal circle from the back of the radiator housing behind the access panel, and then twist the metal chad off with pliers.
6. Tuck the wires neatly into the wiring compartment and replace the access cover.9. Set the radiator breaker to the "On" position. Turn the thermostat up and wait a few minutes.
Place the radiator up against the wall in the position you want. Always respect the manufacturer's warnings regarding minimum distances from the floor, curtains, furniture and other obstructions or combustibles. Look through the upper space in the front of the radiator housing and determine which holes in the housing line up best with the wall studs. If the old radiator was well-fastened, you can use the old radiator mounting holes as a guide, or reuse the holes if possible. Fasten the radiator to the wall by driving screws through the appropriate holes and into the wall studs. You should use one screw near each end of the radiator, and at least one intermediate screw for radiators longer than 3 feet. Tighten the screws until snug, and then back them off half a turn to prevent radiator pinging during the on-off heat cycling.
8. Connect the wiring according to the wiring diagram supplied with the heater. With most models the black wires should be joined together with a wire nut, and the white wires should be joined together with a wire nut. The ground wire should be attached to a screw or bolt that is attached directly to the radiator metal housing, and is clearly labeled for this purpose. Use a stud finder to locate the wall studs and mark them with a pencil.7. Pull the power supply wires from the wall through the hole in the back of the radiator wiring compartment.
Check the radiator to be sure it is heating. Set the thermostat to a comfortable temperature.
