Punctures flatten the F-150's tire, necessitating replacement.
Way hazards such as debris in the roadway puncture the F-150's tires and assent you stranded along the roadside. Ford equipped their 2002 model-year F-150 SuperCrew trucks with nourishment to pocket money a Apartment lodgings tire. The spare tire and jacking Accoutrement are stowed in storage compartments in the Motor lorry. Removing the Apartment lodgings tire and installing the spare requires basic mechanical skills and can be performed along the roadside in an emergency.
Instructions
Removing the Tire
1. Stadium the Motor lorry on calm sidewalk. Lay the transmission in "Lawns" (or in "Reverse" provided your transmission is jotter). Place the parking brake by fully miserable the parking brake pedal and then turn off the engine. Turn on the hazard flashers provided performing a roadside tire moderate.
2. Retrieve the jack and lug-nut wrench from the rear storage compartment on the passenger side of the Supercrew. Retrieve the jack shaft from the front of the engine compartment on top of the radiator device. Retrieve the spare tire lock primary from the glove compartment.
3. Contain the hooked gratuity of the jack application under the lip of the spare tire lock fundamental. Contain the knob at an angle to engage the lip, then straighten the hold so it locks into the leading.
4.14. Install the lug nuts and tighten them by hand.15. Turn the jack handle counterclockwise to lower the truck to the ground.
13. Lift the tire and align the holes in the wheel with the studs in the hub. Slide the wheel assembly onto the hub.
Pry off the circle trim and rotate cap with the Apartment lodgings gratuity of the lug-nut wrench.
7. Loosen the lug nuts with the lug-nut wrench by turning them counterclockwise one-half turn Everyone. Exercise vigour to schism the torque on the lug nuts.
8. Embrace the jack employ into the gap at the mannequin of the jack, then position the jack under the shove's jack speck. The jacking objective for a front circle on a 4X4 is a raised boss located on the spin's front suspension lower arm. The jacking speck for a front trundle 4X2 is a Apartment lodgings piece on the frame located last the front tire and rotate meeting. The rear jacking points are the rear axle between the embosses equitable persist the revolve meeting and in front of the shock mount.
9. Turn the jack bail clockwise to lift the Motor lorry. Lift the Motor lorry until the turn is crystal of the ground.
10. Remove the lug nuts. Grasp the tire at the 3 o'Watch position and the 9 o'Watch position. Pull the tire to remove it from the hub.
Installing the Spare
11. Remove dirt and debris from the back of the spare tire's shove, then roll the spare tire into position in front of the hub with the tire's valve stem toward you.
12. Evaluate the heighth of the hub against the consistent of the centre of the spare tire. Raise the truck higher by turning the jack handle clockwise if the center of the spare tire is higher than the hub. Continue raising the truck until the spare tire can be installed on the hub without the tire touching the ground.
Press the principal in until it engages and then turn the grip counterclockwise. Carry forward turning the haft counterclockwise until the spare tire is lowered to the ground underneath the Motor lorry and there is sufficient slack in the loading cable to pull the tire toward you. Pull the tire toward you and remove the cable retainer from the centre of the spare tire.6.
Position revolve blocks on the tire diagonally different the tire you are changing. Block both front and rear sides of the tire.5. Encompass the jack manipulate with the clue equipped over the bumper gap following to the left licence plate headlight.
Remove the jack.
16. Tighten the lug nuts with the lug-nut wrench in a star pattern. Torque the lugs nuts to the proper foot-pounds with the torque wrench. If your wheels have five lug nuts or 14mm wheel bolts, tighten them to 150 foot-pounds. If your wheels have seven lug nuts or 12mm wheel bolts, tighten them to 100 foot-pounds.
17.Install the wheel trim and cap with a rubber mallet. Return the jack and wheel-lug wrench to the storage compartment.
18. Install the spare tire lock key onto the jack handle again. Lay the flat tire on the ground behind the truck with the valve stem facing up.
19. Slide the tire under the truck until you can insert the retainer into the center of the wheel. Insert the retainer, then position the tire under its stowage compartment.
20. Insert the jack handle with the key equipped through the bumper hole. Press the key in until it engages and then turn the handle clockwise. Continue turning the handle clockwise until the flat tire is raised into the stowage compartment. The mechanism ratchets when the wheel assembly is fully raised.
21. Remove the wheel blocks. Return the jack handle and the spare tire lock key to their respective storage locations.
